When Do You Consider Replacement Balboa Circuit Boards?

 

Circuit boards are essential features for every spa pack as they control the overall function of your spa or hot tub. They keep the water hot and jets bubbling. These boards are a bit like the nerve center of the spa system. 

The circuit boards are the integral parts of the spa systems that send electronic messages to heat the water, switch on or off the pump, etc. Usually, they are metal plates with wires, resistors, capacitors, and relays running around them in a complex grid. In addition, the circuit boards might have transformers and spa fuses mounted on them directly. 

Likewise, every metal part, the water, and the other elements can badly impact the wiring and connections of circuit boards. If the delicate wires don’t connect properly and can no longer communicate, they will affect the functionality of the entire spa system. Therefore, whenever a hot tub or spa system stops working the way it should, you need to check the circuit board first. If it works fine, you can move on to other parts of your hot tub. 

When you find issues with your circuit boards, you need to switch off the spa and switch it on again. First, unplug the entire unit for several seconds and switch it back on. Though every hot tub or spa system has a slightly different setup and circuit boards, there are common ways to troubleshoot the issues. 

You may find a display on the control panel showing error codes. These codes will help you out if you have your user manual. The issues with the circuit boards can be caused due to the electric current from the source or other factors. Read a few possible causes that you can identify and fix quickly. 

• Debris in the heat pump 
• Dirty filter 
• Jets installed improperly or turned off at once frequently 
• Other defective parts like cable, pressure switch, or the circuit board 
• Short in the heating element 
• Blown fuse
• Tripped circuit breaker 
• Poor working pump 
• Blown motor 

There are so many factors causing your circuit board. It can be due to faulty topside control. Moisture can cause the wrong things to switch on with the wrong button. Part of the circuit board can be overheated and melted or burned. 

So, you can check every wire with a meter to locate the exact problem. It is better to call the spa or hot tub manufacturer before troubleshooting the circuit board problems. They will suggest you simple steps to get started, and they may save you time and provide repair parts. If you need help with Balboa spa circuit boards, contact the Northern Lights Cedar Tubs Direct team today at 1-800-759-8990.

4 Common Signs to Replace Your Balboa Spa Heater

 

A Balboa spa heater stops working due to so many reasons. It may be due to issues with the Balboa heater tubes or the spa controller. Read the post and know when you need to replace your Balboa spa heater.

1. Check the water flow.

Your Balboa spa heater works efficiently on adequate water flow. A pressure switch connects to the heater chamber that detects the water flow. If the flow of water is too low, the heater stops working.

If this is an issue with your spa heating system, repairing the spa heater parts is unnecessary. The problem can be due to a dirty spa filter. You must remove the spa cartridge, clean the filter and check the pressure or flow rate. Other causes can be clogged spa jets or pipes, a broken pump impeller, or a broken valve. They can often reduce the water flow into your spa or hot tub, causing the spa heater to stop working.

2. Check the thermostat.

The thermostat is the dial you turn to increase the heat. Currently, most hot tubs have a solid-state thermostat connected to the circuit board. If you use a knob rather than a red arrow, you need to check your thermostat to know whether the unit is faulty or a corroded sensor bulb.

3. Check the high-limit switch.

The high limit switch is another switch like the thermostat and pressure switch. It helps in preventing the spa heater that won’t turn off. The system has maximum heat wherein the switch opens and shorts the electric circuit that brings power to the spa heater element. Use an amp meter or OHM meter to test your spa components.

4. Check the Balboa heater tubes.

Heater tubes are the essential elements of every spa heater. However, they can buildup scale from the hard water or salt systems used. If scale builds on the heater tubes, it will minimize heat and make the tubes stop working.

Eventually, your Balboa hot tub heater will fail to work. Likewise any heating element, most heater tubes have a life span of around five to ten years. Maintaining proper water chemistry is essential to prolong the lifetime of Balboa heater tubes.

If you have a Balboa heater and the heating element stops working, you will not need to replace the entire system. Instead, you need to replace the Balboa heater tubes. The Balboa heater tubes come with two flow sensors, stainless steel houses, and new 2” heater unions.

Replacing the Balboa heater tubes is very simple, and you can do it independently. So, you should buy replacement Balboa heater tubes from Northern Lights Cedar Tubs Direct. You will receive complete support, including detailed instructions on installing your Balboa hot tub heater tube.

Bottom Line –

Now you know the signs to replace your Balboa spa heater. If you need further information on replacing the spa heating systems, please contact Northern Lights Cedar Tubs Direct at 1-800-759-8990.