Thursday 17 December 2020

5 Common Symptoms of Spa Pump Failure

Do you use spa pumps often? If yes, you can use a quality spa pump in an average of five to ten years. If you’ve used your spa pumps more than five years and started showing problems or major breakdowns, it’s better to consider spa pump replacement rather than troubleshooting different components.

Understanding a Spa Pump

Generally, a spa pump is an important piece of equipment for a spa or hot tub. It draws water into the filtration system where its momentum pushes water through the filter, heater and spa jets prior to water going back to the spa.

A spa pump comprises of two main components like a motor and wet end. Generally, the motor powers up the impeller which is present inside the wet end. The impeller starts propelling the water through a discharge port on the pump present on the side or center part of the house.

This spa pump is available in one or two speeds and has horsepower that ranges from 1/8 HP for spas that only require water circulation to 5 HP for spas with a large number jets. There are different pumps available to fit any size or setup of any spa.

Spa Pumps

5 Common Symptoms of Spa Pump Failure

There are so many reasons behind the failure of spa pumps and some of the best symptoms are discussed below:

1. Leakage

If the frames are loose, they may cause water to escape and propel through the pump. It’s suggested to check the frames and o-rings to make sure that they are fully secure and tight. Leakage causes when there’s a faulty pump seal. You should change the pump seal to make sure that your pump gets a tight and leak-free fit.

2. Low Water Pressure

If the water pressure is low, it may be due to some sorts of obstructions. They may prevent the impeller from turning on. Check the impeller and remove any debris if present to prevent blocking further.

3. Unnecessary Noise

If the bearings are worn, they can produce humming sound and prevent the motor from functioning properly. You need to check the bearings for dirt or corrosion and replace them if you find them worn. Don’t forget to check the motor coupling, brackets and other connected parts. Make sure that all the screws, nuts and bolts are perfectly connected and fully secure.

Spa Pumps

4. Overheating

However, you can keep your hand on a spa pump safely under regular conditions. When it produces more heat with the increase in temperature, it releases unnecessary energy. Therefore, overheating can occur, especially when there’s not sufficient clean air flowing through the motor. If it’s the case, it can be due to the motor. Therefore, you should place your spa pump in an area without any dirt and leaves.

5. Defective Motor

If your motor is not functioning properly, you should check whether the power switch is one. If it is and still not working, check whether there are any failed relays, burned out wires or a blown fuse. Inspect all connections like copper bonding wire and pump power cable and identify any possible signs of damage.

Bottom Line –

When you find any above-discussed signs of spa pump failure, you should consider buying spa replacement pumps from Cedar Tubs Direct. For more information, feel free to give us a call now at 1-800-759-8990.

Saturday 12 December 2020

Buying Balboa VS520 Hot Tub Heater and Spa Pack

Do you have a costly spa or hot tub heater that requires the spa pack upgraded or replaced? This is where the Balboa VS520 – premium hot tub system comes in. It’s the unit that can handle nearly every combination of electrical requirements. This hot tub heater and spa pack uses the latest M7 technology, the best spa technology available on the market. It has completely digital circuitry which means less failure, more accurate heating and simple to use.

The Balboa VS520 hot tub heater is a premium hot tub heating kit perfectly designed to retrofit even the most existing spas. It features with a plastic exterior in order to protect against water entrance and corrosion. Its 5.5w heating unit can be installed into the existing PVC plumbing and can be wired for 60Hz and 240VAC convertible power.

The use of integrated connectors in the circuit board makes the installation process easy and its effortless design eliminates the unnecessary energy costs. This spa heating pack comes with a heater unit, the circuit board and sensors.

Balboa VS520

In addition to, the Balboa VS520 has some of the built-in programmable features like cycle programming, freeze protection, economy mode, sleep mode and self diagnosis. Also the Balboa spa heater has the ability to choose how much current will be drawn by choosing the number pumps to run. It has receptacles for two 2-speed pumps, one speed pump or blower, one circulation pump, one ozonator, one constant-on for audio or visual devices and one 12 volt light. Except light, all the receptacles can be switched to supply 230 volts or 120 volts.

Upon buying a Balboa VS520 spa heater, you will get VS520SZ pack with 2” heater tail pieces, plasticized control instruction sheet and complete instruction manual for retrofit situations. However, the VS520 spa heater belongs to the Value Series (VS) family of hot tub control systems. As discussed above, this system is designed using Balboa’s patented M7 temperature and water flow sensor technology as well as completely new universal control platform.

Here are a few best reasons why buying a Balboa VS series spa heater makes perfect sense:

Perfectly designed for ease of installation and service –

The Balboa VS520 is based on the common universal platform that enhances feature flexibility while minimizing installation and configuration related issues. The VS family spa heater comes with unique, good feature flexibilities whereas its performance is competitive with much high-end products.

The M7 technology helps the system in eliminating more failure prone pressure switches and simplifies the installation without drilling additional holes inside the spa.

Ultimate flexibility and feature-rich

The Balboa VS520 hot tub heater has a plastic enclosure to get rid of water intrusion smoothly. The connectors present on the circuit board minimize wires and simplify the service.  The system has a single two speed pump, or an additional pump or a blower. The hot tub heaters feature a convertible power supply that can be wired for 120 or 240 volts, a 5.5 KW heater and support VL panels.

Improved reliability

Currently, most people have been using the M7 technology. The VS series of spa control systems are built using M7 technology that will deliver optimal performance and satisfaction. This universal control platform increases flexibility and reduces configuration related hassles.

Final Consideration –

When it comes to installing a Balboa VS520 hot tub and spa system, it’s wise to look no further than Cedar Tubs Direct. Please check out our available Balboa VS520, please visit our website at https://www.cedartubsdirect.com.

Friday 27 November 2020

Understanding the Basic Details of Hot Tub Plumbing System

More often, sauna bathers never give a second thought to hot tub plumbing in Canada. When it comes to enjoying hot tub sessions, all you want is to focus on relaxation and enjoyment. You won’t need to figure out how water gets pushed through the jets. 

At least once in a while, you should find yourself wondering how your hot tub creates soothing and tranquil ambiance. Take a look at this post and understand better about hot tub plumbing systems in Canada:

Understanding the Basic Details of Hot Tub Plumbing Kits 

Now it’s time to get started with an empty hot tub. First of all, you should know what will happen when you fill it with water.

Skimmer and Suction Line –

Suction line will start sucking in water whereas the skimmer will remove debris like leaves, insects, etc. Both the skimmer and suction line are responsible for sending water to the pump.

Filter and Pump –

After that, the suction line collects the water and the skimmer takes it to the pump. The pump pushes the water towards the filter. When the water passes through the filter, it will remove any small contaminants like dust and dirt particles. 

Hot Tub Plumbing in Canada

Manifolds and Heater –

The filtered water goes to the heater. The heater uses its heating element to make the water toasty and nice. As soon as water gets heated, the water starts flowing through the hot return line and goes to the manifold. 

Generally, manifolds are water diverters and absorb water from a single source. After that, manifolds divert it to different places. 

Water Jets –

When the water gets hot and clean, it will flow from the manifolds to the jets in a hot tub through a number of flexible PVC pipes. At the end, jets push out the water to reach you. 

Different Elements of Hot Tub Plumbing System 

Apart from the above discussed elements, there are other elements of hot tub plumbing systems that you need to know:

Air Control 

Hot tubs are able to draw in air and expel them through the jets while offering a pleasantly bubbly effect. The availability of simple to use air control valves makes it possible. 

Sanitation –

All you need to have is an effective sanitization to ensure optimal safety and sanitization while enjoying hot tub sessions. Traditionally, either chlorine or bromine is used for sanitization purposes. You will have to sanitize your water by adding those chemicals in liquid, tablet or powder form. 

Apart from sanitizers, you can add a few things to your hot tub plumbing in Canada. For instance, you can buy an ozonator. The ozonator receives water once it’s heated and filtered. Bacterial busting ozone molecules are present in the ozonator to add to the water. 

Typically, this is true for salt water sanitation systems. Once the water gets hot and clean, it should be better sanitized prior to being pushed into the hot tub. 

Maintain your hot tub plumbing system –

A plumbing system is paramount for your hot tub plumbing kit. Your hot tub would be nothing more than a bucket of water. Therefore, you should take care of your plumbing system. This way, you’ll make sure that you provide enormous fun and relaxation to you and your near and dear ones. 

Bottom Line –

So, what are you thinking about hot tub plumbing in Canada? Feel free to reach out to Northern Lights Cedar Tubs Direct team as soon as possible. Contact us today and we’ll get back to you right away.

Sunday 15 November 2020

5 Questions to Ask Yourself before Buying a Hot Tub

When you’ve finally decided to buy a hot tub, you may be flooded with plentiful choices to choose from. However, hot tubs have been around for a quite long time so it’s obvious that there are so many models to choose from than the dish soaps or soda pops.

You often ask yourself, “What hot tub you should buy?” Ultimately, it will be a personal choice. So we’ve come up with a post that will focus on so many questions you should remember when deciding to spend your money. Your decision on hot tub depends on so many things including types of spa heaters you want to go with. Besides, there are much more to consider; read on to know more:

Spa Heaters

1. Who will use the hot tub?

If you want to use the hot tub, you should get the go-ahead from your doctor or are already enough to utilize a hot tub without any issue. After that, you should ask yourself who is going to use it. It doesn’t make sense to have a 2 person hot tub if you have a 5 person family.

Obviously, someone will b always left out and it could greatly impact on your family atmosphere. If you foresee yourself entertaining more often, you’re going to need a bigger size tub. Remember that, hot tubs act like magnet that appeal people, even if you don’t invite them. Therefore, you should plan accordingly.

Spa Heaters

2. What is the type of your body?

Most of the current hot tubs come with molded seating. This means if you’re taller than average, you may get a hard time being comfortable in a hot tub. Even if you’re quite short or different size from the average, you may feel uncomfortable. Therefore, it’s highly suggested to test your potential hot tub in person when it’s filled with water to make sure it fits you in the best way as possible.

3. Where will you install the tub?

When it comes to choosing the location, you should make sure it has the ample amount of space and accessibility. It will play a key role in hot tub selection. The important thing you want to have is a hot tub sitting in your driveway. It’s impossible to install it without doing major renovations to your yard or house. Hence, it’s better to handle beforehand. So, make proper measurements again and again.

Spa Heaters

4. How much do you want to invest?

Set a right budget and it will help you narrow down the choices you have when buy a hot tub. If you’ve very small budget, you’ll likely end up with an inflatable hot tub. It’ll do the job just fine; but won’t last long. If you have more, you can go for more durable and highly efficient hot tubs for your needs.

5. What type of hot tub accessories do you want?

Hot tub accessories become a matter of preference when choosing a hot tub. Of course, the fewer you get; the less you’re going to spend. But you want to feel comfortable all the time. You’ll likely invest in jets, energy efficient spa heaters and an insulated hot tub cover. Ease of maintenance, accessibility, repairs and good warranty can be paramount for people who are busy or don’t have enough DIY skills.

Bottom Line –

For the purchase of all types of hot tubs, hot tub accessories, spa heaters, you should choose no other than Cedar Tubs Direct. We have the durable, highly efficient hot tubs and supplies to deliver you an enormous experience. For more information, please visit our website at https://www.cedartubsdirect.com/balboa-spa-heaters-c-115_146.html.

Saturday 10 October 2020

Buying Balboa EL2000 Elite Series Spa Pack for Advanced Spa Heating

Balboa EL2000 Elite Series spa pack is the most advanced spa pack of Balboa Elite series. This spa pack is ideal for both commercial and residential spa owners seeking for additional sophistication in control options. Even, it’s perfect for those who need remote or wireless control and monitoring.

Balboa EL2000 comes with 5.5-1.5 KW Digital Spa Controller and multiple control options like ozone suppression, clean up cycle after use, panel lock, and real time clock. The real time clock feature allows you set the filter cycles by the time of a day and on a 12 hour or 24 hour cycle.

This spa pack supports both 12 volt and 120 volt lights and fiber optic wheel lighting. The Elite series supports wireless RF remote control and monitoring through computer software applications and modem or high speed networks.


Balboa EL2000 uses M7 technology, the best spa pack technology available on the market. This Elite series spa pack has complete digital circuitry ensuring less failure and more precise heating range i.e. +/- 1 degree F. It can work effortlessly at 120VAC and will produce 1.4 KW heat. The system can be used at 230 VAC and will produce 5.5KW heat.

In addition, you can add one or more auxiliary heater – each producing 5.5KW to the unit. This EL series spa pack fits standard 2” piping, an ideal alternative to upgrade any mechanical or digital spa pack.

Balboa EL2000 has built-in programmable features like filter cycle programming by time duration or time of the day, different power saving modes like sleep mode, economy mode, standard economy mode, ozone suppression, clean up cycle, freeze protection, panel lock, temperature lock, standby mode for changing filter, sophisticated diagnosis and reminder measures, etc.


This Elite series spa pack is able to choose the amount to be drawn allowing a breaker as low as 30 AMP and deliver complete 5.5 KW electric heat. This spa pack has receptacles like 2-speed pump 1, one 1-speed pump 2 that can be altered to handle a 2-speed pump, one blower or 3rd pump 3, one circulation pump, one ozonator, one constant on for audio or visual devices, one 12 volt light or LED or fiber wheel, etc. All of the receptacles can be switched to supply 230 Volts or 120 Volts.

The spa pack has EL2000M3 pack with 2” PVC heater tailpieces. It comes with complete instruction manual to handle retrofit situations produced by Northern Lights. Though it’s made with patented M7 technology, the spa pack eliminates the requirement for pressure sensors and remote heat sensors which are quite common on other older spa packs. This advanced spa technology allows spa pack to keep it in any location or direction before or after the spa pump or before or after the filter.

Are you thinking to invest in Balboa EL series spa pack? If yes, then you should look no further than Northern Lights Cedar Tubs Direct. For more information about spa packs, feel free to contact us as soon as possible at 1-800-317-9054.

Thursday 17 September 2020

Why Do You Buy Bromine Pool and Spa Tablets?

Currently, proper sanitization of your spa or pool is important to stay safe and protected during this COVID-19 pandemic situation. Therefore, buying right hot tubs chemical products makes really sense.

Now it’s easy and efficient with Bromine Pool and Spa Tablets available at Northern Lights Solar Solutions. All you need to do is to fill up pucks in your standard spa tablet dispenser. This way, you will leave your spa clean and properly sanitized.

These bromine tablets are approved to use for all varieties of wooden hot tubs, spas and pools. They are specifically formulated to work with different hot tubs and spas. Northern Lights bromine tablets work really well with standard spa puck dispensers.

Hot Tubs Chemical

They are able to control the growth of bacteria and algae in spa water. If you use them as directed, they work effectively like spa water sanitizer and disinfectant.

You should fill the dispenser and make adjustments on dial to maintain ideal sanitization level for the water volume as per the water test reading. You may think why you use bromine over chlorine for the sanitization of your spa or hot tub at home. Here are a few reasons why using bromine rather than chlorine is a must:

Chlorine pucks are available with shelf life. After using them one and half year, gas trapped in the powdered pucks could escape easily. But bromine tablets have no shelf life.

When chlorine kills bacteria, it becomes inert. When you add spa shock to your spa, it regenerates bromine salt into bromine. It means adding spa shock will make the bromine last much longer than chlorine.

Hot Tubs Chemical

Using chlorine in spa water can help you fight against algae more effectively. But bromine is much efficient in killing harmful bacteria and virus.

When you use chlorine, it will combine with ammonia and nitrogen in spa water. It will result in several problems like red eyes, itchy skin and awful smell. But bromine doesn’t combine with ammonia or nitrogen and doesn’t offer negative side effects.

While using high temperatures in a hot tub, chlorine gets active and tends to dissolve into its gas form. As a result, it will lead to inefficiency. Bromine remains intact in the heat of a hot tub.

Hot Tubs Chemical

Upon getting in contact with high pH level spa water, chlorine loses around 75% of its sanitization ability. The high pH level results when multiple users use a space at once. But bromine remains unaffected by high pH levels nearly.

Are you thinking to buy hot tubs chemical products online? You should look no further than Northern Lights Cedar Tub Direct. For more information about our hot tubs chemical products including bromine tablets, feel free to contact us at 1-800-759-8990.

Sunday 6 September 2020

How Can You Keep the Spa Pumps in Top Condition?

Spa pumps are considered as the lifeline of your hot tub or spa. They pump water in and out of the shell. The pumping process combines chemicals throughout the hot tub and filters out any harmful contaminants or debris particles. After that, these pumps run through the spa heater and jets.

In short and simple worlds, pump is the heart of your spa and works like your heart as it delivers healthy maintenance and ensures productivity.

Spa Pumps

Focus on regular maintenance.

First of all, you have to maintain your spa pump on a regular basis. You have to make sure that your spa has properly balanced water. It will prevent scale buildup and the pool equipment erosion.

Balanced water means maintaining proper balance of minerals in your spa water. As a result, your sanitizer will work more effectively and feel much softer and cleaner to your skin.

Check for the pH level in the spa water. If it’s high, it will significantly cause scale buildup in and around the spa including the pool pump and filter. However, the higher pH level will make your pump work much harder than usual which will ultimately impact on the lifetime of the pump.

If the pH level is low, the water inside your hot tub or spa will be acidic. It can be a hassle to your pump as well as all the spa components. The acidic water corrodes your spa equipment.

Spa Pumps

Make your spa free of dirt and debris.

Check the water pressure in your hot tub. If you find it low, it may be due to buildup of debris or obstructions that blocks the impeller from working. Therefore, it’s highly suggested that you should check and clean your spa filter pump regularly.

Consider the location of your spa pump.

If you install your pump in an area with dirt and debris, they can block the airflow within your pump, overheat the motor and lessen the durability of whole unit.

Another issue you have to consider is the existence of water around the hot tub pump. Presence of water can reduce the lifetime of your spa pump. Hence, you should check for leaks on your spa pumps. More often, you need to tighten the o-ring or loose frame to fix these leaks.

Spa Pumps

If the worst scenario approaches, you may require changing a seal to make sure that the leak is fixed. Even, it’s more convenient to consider replacement spa pumps.

Keep your ear open.

You have to listen whether any humming, grinding or whining noise coming from the pump. If yes, then it may be due to worn out bearings. Check the bearings whether there’s any sign of corrosion or dirt buildup. It’s better to replace the worn out bearings as soon as possible.

Bottom line –

When it comes to spa pumps, generally they have 5 to 10 years of lifetime. If you follow regular maintenance schedule, it will significantly impact on the longevity of the spa pump.

Again if you need replacement spa pumps, you should rely on Northern Lights Cedar Tubs Direct. We stock an extensive selection of spa pumps to choose from. Choose your spa pumps precisely so that you can enjoy your spa more knowing that it’s ready for fun and entertainment throughout the year.

If you’ve questions regarding your spa pump, feel free to reach out to us at 1-800-759-8990!